The PosiBand contact system has many advantages over the legacy split tine design.
- PosiBand is more robust - no split tines to be pried open in harsh environments, resulting in reduced normal force and degradation of electrical performance.
- PosiBand has greater surface area at the male and female contact interface, resulting in more consistent electrical performance.
- PosiBand has lower average insertion forces, resulting in greater ease in mating, especially in larger high density connectors.
- The PosiBand’s main contact body does not require annealing of the crimp barrels, as does the split tine design. This eliminates concern of unintentionally heat-treating the mating end of the contact, which can cause electrical failure.
High reliability connectors utilize female closed entry contacts that provide an unbroken ring of solid material at the face of the contact. The closed entry feature is crucial in preventing damage to female contacts used in harsh environments, repeated mating cycles, blind mate applications and applications requiring highest reliability.
The most common closed entry design utilized by D-subminiature connector manufacturers is a split tine and sleeve concept. The main part of the contact has split tines to provide normal force on male contacts when connectors are mated. A sleeve is placed over the main part of the contact to provide a closed entry.
The sleeve surrounding the split tines offers greater contact reliability when compared to a similar contact that does not have a closed entry feature. The sleeve serves to limit the distance the contact tines can open. If female contact tines open too far, they may not return to their original position. This may cause diminished normal forces and can result in intermittent or open electrical circuits.
Female contact tines can open too far if an oversized pin is inserted into the contact. The most common cause for damage can occur if a male contact is inserted into a female contact at an angle. Rocking the connectors back and forth during mating and unmating can pry the female contacts open.
Utilizing a sleeve to provide a closed entry feature does allow split tine contacts greater reliability. This design has been used for decades because it provided a degree of reliability at an affordable price. However, split tine contacts are still susceptible to being pried open if care is not taken when cable connectors are mated and unmated to other cable or board mount connectors.
The split tine design has other inherent weaknesses. One of these is the need to anneal the crimp barrel.
The material used to manufacture split tine female contacts must have elasticity to allow the tines to open when receiving the male contact and then to return to their original position after the male contact is disengaged. Unfortunately, elasticity is not a characteristic that is desirable for the crimp barrel. When crimping a wire onto a contact, the material needs to be ductile to allow a permanent set after the crimping operation.
Split tine contacts are manufactured using a material with elastic properties. The crimp barrel is then annealed to soften the material so a proper crimp can be achieved. If the annealing process is not carefully controlled, the mating portion of the contact may unintentionally be annealed. This will result in diminished normal forces and potential electrical failures.
Other weaknesses of split tine contacts revolve around the fact that the tines must be depressed to provide normal force. The depressed tines slope inward and form a "point" at the mating end of the contact. If the forming operation is not carefully executed, proper normal force will not be achieved. Also, since the tines slope toward a point, there is a reduced area of contact between the male and female contact interface. The interface consists of a small ring at the tip of the female contact. Electrical contact depends solely on this small area between the male and female interface.
Positronic's new PosiBand technology takes a unique new approach for D-subminiature contacts, eliminating many of the weaknesses of the split tine design.
PosiBand contacts utilize a two-piece contact design. Each piece serves a separate function. The main body of the contact provides the mechanical platform for the contact system. This includes a true closed entry contact opening. The PosiBand spring clip provides normal force on the male contact.
The PosiBand system does not have a split tine female contact that can be pried open during the mating process. Instead, it uses the PosiBand spring clip, which is very robust and less susceptible to damage. The PosiBand system is much more rugged than traditional D-subminiature female contact designs.
Another important feature of the PosiBand system is the use of brass to manufacture the base contact. Brass has excellent properties in relation to crimping wire onto contacts. This eliminates the need to anneal the contact, avoiding the potential for intermittent or open electrical circuits due to improper heat treating. The base contact can be made of brass because the PosiBand spring clip provides contact normal force. The spring clip is made of spring tempered Beryllium copper.
The Posiband system also increases the interface area between male and female contacts when compared to the sloped design of split tine contacts. The greater contact area provides more reliable electrical integrity. On a micro level, there are a greater number of electrical paths through the contact interface. The greater contact area provides better resistance to discontinuity during vibration. The greater contact area may also minimize the effects to electrical performance due to corrosion over time.
Greater contact area provided by the PosiBand system does not increase insertion forces; in fact, the PosiBand design provides a more consistent insertion force value, which results in a lower average insertion force when compared to the split tine design.
When tested to U.L. 1977, the current rating for a size 20 PosiBand contact system is 14 amps with six contacts energized. The current rating for a size 22 PosiBand contact system with six contacts energized is 10 amps.
PosiBand parent technology has been utilized in connectors, including MIL-DTL-28748 military connectors, for decades. Specific PosiBand technology has been used by Positronic for many years and is now being imported into other products.
Positronic is now offering the PosiBand system in standard density and high density D-subminiature connectors, as well as combination D-subminiature connectors. Other Positronic products will utilize this advanced contact system in the near future.
The PosiBand contact design is compliant to SAE AS 39029 test requirements. Positronic is currently working with applicable organizations to gain approval to use the PosiBand system in MIL-DTL-24308 D-subminiature connectors and SAE AS 39029 contacts. We expect this approval in late 2009 or early 2010.
Lastly, although other alternate contact interface designs in the marketplace carry a heavy premium in cost, this is not the case with the PosiBand. Products using the PosiBand system will be priced the same as products using the previous design.
Please contact your local Positronic representative for more information about this revolutionary design. To find a Positronic representative near you, view our Sales Offices.
Feeds